Ampac FireFinder PLUS Specifications Page 88
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 82
FIREFINDER PLUS
(
AUST
)
INSTALLATION
,
COMMISSIONING OPERATION
RESERVE AGENT
(Yellow) Illuminated when the “Reserve Agent” is selected.
Local Control Panel Inhibit
The agent inhibit switch has an internal lamp fitted with yellow lens. Illuminated when the inhibit switch
is activated at the FACP or any of the LCS’s.
Buzzer (located at the FACP)
The Buzzer sounds;
Under all fault conditions and can be silenced by using the appropriate FACP buzzer
silence control.
When the LCS Inhibit control is activated – after 8 hours – treated as an isolate condition.
When the service inhibit is activated - after 8 hours – treated as an isolate condition
Connecting the LCS to the Agent Termination Board
1. ISOLATE THE AGENT
2. Check the FACP is functioning correctly then power down
3. Connect the LCS to the Agent Termination Board within the Fire Alarm Control Panel and
Interlock as shown below. If applicable take into consideration warning signs at this point
4. Insert the link LK1 onto the last LCS in the chain. If un-used place the link onto one of the LK1
pins
5. Set the address of the LCS,
6. Power up the system and program the FACP for the addition of the LCS
7. Check the FACP is functioning correctly and test
8. De-isolate the Agent
CAUTION - TO PREVENT ACCIDENTAL AGENT RELEASE DO NOT DE-ISOLATE THE
AGENT UNDER ANY CIRCUMSTANCES UNTIL THE SYSTEM AS A WHOLE IS FUNCTIONING
CORRECTLY
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
2
3
4
+27VDC OUT
TO NEXT LCS
+27VDC IN FROM
TERMINATION BRD.
10K
EOL
+
ON
Address
Switch
Set to 1
1 2 3 4
Agent Termination Board
within the FACP
Local Control Station
ONLY USED ON THE LAST
LCS ON THE COMMS BUS
10K
EOL
2K2
INTER
LOCK
INSERT A 2K2 ACROSS
THE 10K EOL TO
DEFAULT TO "ON"
TB4
T1
CN1
LK2
TB2
TB1
SW2
4
3
2
1
LK1
CN5
+
AGENT
MANUAL HOLD/
MANUAL
-
+
RS 485 OUT
RS 485 IN
-
+
RELEASE
0V+24V
COM
LINK
TERMINATOR
COM
0V+24V
BRD25ARB5-
INTER-
LOCK
-
JTAG
INHIBIT
SWITCH MON.
DISABLE
INHIBIT
EOL
SIG
SIG
SCRN
27V
0V
+
+
-
TB1
RS 485 COMMS BUS
Figure 103: PCB Layout & Cabling Details
- Disabling a Zone / Device 3
- 2 Introduction 8
- 2.3 Compliance 9
- NOTE: WIRING MAY VARY DUE TO 10
- CLIENT PANEL CONFIGURATION 10
- FireFinder PLUS Description 11
- 4.5 Cabling Recommendations 14
- Page 11 17
- 22/09/09 18
- BRD86BPSC4 18
- 4.8.1 Battery Connections 19
- 4.8.3 Monitored Inputs 20
- 4.8.4 Monitored Outputs 21
- Page 16 22
- 4.9 Main Board 23
- KEYSWITCH 24
- BRD86FPB4 24
- 11/08/10 24
- 4.11 Main CPU 25
- 4.12 Slave CPU 26
- Page 21 27
- Page 22 28
- 5.1 System Controls 29
- Page 25 31
- Page 26 32
- 5.2 System Indicators 33
- Page 28 34
- Page 29 35
- 6.4.1 Forgotten Passwords 37
- 7.7 Status 41
- 7.8 Tools 45
- 7.9 Setup 46
- 7.10 About 47
- 8 The Function Menu 48
- to initiate a WALK TEST: 50
- 8.6 I/O 51
- 8.7 Global (Network Panels) 52
- 8.8 Passwords (Level III) 53
- Device 55
- 8.9.9 Mismatch Detected 58
- Page 53 59
- LOOP OR DEVICE 61
- Note: Debug/Noteboo 62
- 12.1 Ancillary Services 63
- 12.3 Expansion Board 64
- Page 59 65
- RS485 Control 66
- Comms Out 66
- 12.7 16 Way Input Board 68
- 12.8 8 Way Relay Board 69
- 12.8.2 Remote Relay Board 70
- - + 71
- 12.10 4 Way Fire Fan Module 72
- 27VDC Out27VDC In 73
- 12.12 Bargraph Display Card 74
- 12.14 SmartTerminal 75
- 12.14.2 Mechanical 76
- Page 71 77
- 12.14.5 Operation 78
- 12.15 Agent Release Control 82
- Page 77 83
- Page 78 84
- 12.15.2 Agent Release Module 85
- Page 80 86
- Page 81 87
- Page 82 88
- Comms In 89
- 12.15.5 Interface Wiring 90
- 12.15.6 Warning Signs 91
- Page 87 93
- Page 88 94
- Polarised 3 Wire Connection 94
- 12.17 Printer 98
- 12.17.2 Maintenance 99
- Page 94 100
- Page 95 101
- IMPORTANT 102
- Page 97 103
- Page 98 104
- Page 99 105
- List of Compatible Devices 106
- AMPAC TECHNOLOGIES PTY LTD 107
- 16.1 Maintenance 108
- Page 103 109
- 17 Compatible Devices 110
- 18 Address Setting 112
- 19 Glossary of Terms 113
- 20 Definitions 114
- 21 Specifications 115
- Page 110 116
- 22 QUICK REFERENCE GUIDE 117
- 23 Statement of Compliance 118
- Page 113 119
- Print Name/s 119
- Please PRINT or Stamp 119
- 23.1 Installation Details 120
- Commissioning Test Report 121
- 24.1 Procedure 122
- 24.2 System Information 122
- Page 117 123
- Page 118 124
Related products and manuals for Fire protection Ampac FireFinder PLUS
Fire protection Ampac ZoneSense User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.654 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals