Ampac FireFinder PLUS Specifications Page 124
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 118
FIREFINDER PLUS
(
AUST
)
INSTALLATION
,
COMMISSIONING OPERATION
(ii) There are no ‘blind’ spots in the area protected.
(iii) Detectors are rigidly fixed.
(iv) Detector lenses are clean and adequately protected from dus
t
and extraneous radiation sources.
(v) Detectors respond to a flame or simulated flame source.
(x) Multi-point aspirating smoke detectors:
(i) Response time of all sampling points meets the requirements o
f
AS 1670.1.
(ii) Alarm settings and indicators operate correctly.
(iii) Remote indication of alarm and fault signals operate correctly.
(iv) Airflow failure indicator operates correctly.
(v) System (signal) failure indicators operate correctly.
(vi) Isolate and reset functions operate correctly.
(vii) Alarm and fault test facilities operate correctly.
(y) Duct sampling unit: The alarm indicator is clearly visible from a
trafficable area and the duct air velocity exceeds the minimum
velocity specified for the unit. If not, the measured differential
pressure is at least the minimum specified for the unit.
(z) Ancillary control functions: Each ancillary control function
operates with the activation of associated alarm zones.
(aa) Alarm signaling equipment:
A
larm signaling equipmen
t
initiates a fire alarm signal to the monitoring service provider.
(bb) Labeling:
A
larm zone location is immediately apparent from the
alarm zone labeling.
DOCUMENTATION
The following documentation is located in or adjacent to the FIP:
(a) ‘As-installed’ drawings.
(b) CIE documentation required by AS 4428.1 or AS 7240.2.
(c) Commissioning test report.
(d) Installer’s statement in accordance with Appendix E of AS 1670.1.
(e) A log complying with the requirements of Clause 7.3 of AS 1670.1.
(f) Aspirating system design tool calculation.
- Disabling a Zone / Device 3
- 2 Introduction 8
- 2.3 Compliance 9
- NOTE: WIRING MAY VARY DUE TO 10
- CLIENT PANEL CONFIGURATION 10
- FireFinder PLUS Description 11
- 4.5 Cabling Recommendations 14
- Page 11 17
- 22/09/09 18
- BRD86BPSC4 18
- 4.8.1 Battery Connections 19
- 4.8.3 Monitored Inputs 20
- 4.8.4 Monitored Outputs 21
- Page 16 22
- 4.9 Main Board 23
- KEYSWITCH 24
- BRD86FPB4 24
- 11/08/10 24
- 4.11 Main CPU 25
- 4.12 Slave CPU 26
- Page 21 27
- Page 22 28
- 5.1 System Controls 29
- Page 25 31
- Page 26 32
- 5.2 System Indicators 33
- Page 28 34
- Page 29 35
- 6.4.1 Forgotten Passwords 37
- 7.7 Status 41
- 7.8 Tools 45
- 7.9 Setup 46
- 7.10 About 47
- 8 The Function Menu 48
- to initiate a WALK TEST: 50
- 8.6 I/O 51
- 8.7 Global (Network Panels) 52
- 8.8 Passwords (Level III) 53
- Device 55
- 8.9.9 Mismatch Detected 58
- Page 53 59
- LOOP OR DEVICE 61
- Note: Debug/Noteboo 62
- 12.1 Ancillary Services 63
- 12.3 Expansion Board 64
- Page 59 65
- RS485 Control 66
- Comms Out 66
- 12.7 16 Way Input Board 68
- 12.8 8 Way Relay Board 69
- 12.8.2 Remote Relay Board 70
- - + 71
- 12.10 4 Way Fire Fan Module 72
- 27VDC Out27VDC In 73
- 12.12 Bargraph Display Card 74
- 12.14 SmartTerminal 75
- 12.14.2 Mechanical 76
- Page 71 77
- 12.14.5 Operation 78
- 12.15 Agent Release Control 82
- Page 77 83
- Page 78 84
- 12.15.2 Agent Release Module 85
- Page 80 86
- Page 81 87
- Page 82 88
- Comms In 89
- 12.15.5 Interface Wiring 90
- 12.15.6 Warning Signs 91
- Page 87 93
- Page 88 94
- Polarised 3 Wire Connection 94
- 12.17 Printer 98
- 12.17.2 Maintenance 99
- Page 94 100
- Page 95 101
- IMPORTANT 102
- Page 97 103
- Page 98 104
- Page 99 105
- List of Compatible Devices 106
- AMPAC TECHNOLOGIES PTY LTD 107
- 16.1 Maintenance 108
- Page 103 109
- 17 Compatible Devices 110
- 18 Address Setting 112
- 19 Glossary of Terms 113
- 20 Definitions 114
- 21 Specifications 115
- Page 110 116
- 22 QUICK REFERENCE GUIDE 117
- 23 Statement of Compliance 118
- Page 113 119
- Print Name/s 119
- Please PRINT or Stamp 119
- 23.1 Installation Details 120
- Commissioning Test Report 121
- 24.1 Procedure 122
- 24.2 System Information 122
- Page 117 123
- Page 118 124
Related products and manuals for Fire protection Ampac FireFinder PLUS
Fire protection Ampac ZoneSense User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.893 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals