ZONESENSE PLUS OPERATION & PROGRAMMING ZoneSense PLUS Fire Alarm Control Panel (AS4428.1) Operation & Programming MAN 1564-2
Page 8 ZONESENSE PLUS OPERATION & PROGRAMMING Brigade Press Enter then Move Right or Move Left to view the Brigade screen. Press Enter then
Page 9 ZONESENSE PLUS OPERATION & PROGRAMMING Sounders Press Enter then Move Left or Move Right to select the required Sounder (1–8). OR Pre
Page 10 ZONESENSE PLUS OPERATION & PROGRAMMING Accessing information on 2 Faults Press Enter Move Right key to scroll
Page 11 ZONESENSE PLUS OPERATION & PROGRAMMING Note: If a Zone has been programmed to be; 1. NON LATCHING the panel will only go into alarm
Page 12 ZONESENSE PLUS OPERATION & PROGRAMMING Battery Test Press the Move Right and / or Move Left key to move to the Battery Test menu, Pr
Page 13 ZONESENSE PLUS OPERATION & PROGRAMMING Main Control Board Outputs Isolates Press Enter to access the Isolate – Main Control Board Monit
Page 14 ZONESENSE PLUS OPERATION & PROGRAMMING If the PASSWORD is accepted the screen will display ACF TRIP RESET. Use the Right keys to move
Page 15 ZONESENSE PLUS OPERATION & PROGRAMMING LED Annunciator Master ( LAM ) This tells the FACP how many LAMs are on the system hence how man
Page 16 ZONESENSE PLUS OPERATION & PROGRAMMING Non Latch Non Latch if set will initiate an alarm only when the Zone is in alarm. SRESET 60 Res
Page 17 ZONESENSE PLUS OPERATION & PROGRAMMING Set the Reset / Buzzer output option so as the output acts as a Reset or Buzzer function as per
ZONESENSE PLUS OPERATION & PROGRAMMING Table of Contents SECTION ...
Page 18 ZONESENSE PLUS OPERATION & PROGRAMMING Fire Fan The sub menu consists of; Alarm Inhibit Function Latch ACF Isolate For: Alarm Inhib
Page 19 ZONESENSE PLUS OPERATION & PROGRAMMING ACF Isolate Press Enter and the cursor will flash over YES or NO and then the Move Up or Move
Page 20 ZONESENSE PLUS OPERATION & PROGRAMMING Zone Labels To name the Zones press Enter then the Move Right and / or the Move Left keys to s
Page 21 ZONESENSE PLUS OPERATION & PROGRAMMING 7 Appendix A: AS 4428 Menu Structure & Programming STATUS FAULTS TESTS ISOLATE SYSTEM PROG
Page 22 ZONESENSE PLUS OPERATION & PROGRAMMING Test TESTALARMTESTZONE 1TESTFAULTTESTWALKTESTLAMPTESTZONE 2TESTZONE 3TESTZONE 4TESTZONE 5TESTZON
Page 23 ZONESENSE PLUS OPERATION & PROGRAMMING System ( Password required ) ALARMYES / NORESOUNDYES / NOBUZZERSYSTEMEARTH MONYES / NOBRIGADEYES
Page 24 ZONESENSE PLUS OPERATION & PROGRAMMING Program AGENT T2AGENT T1SREST 60AVFSELECTZONE 1 - 8NORMALZONESSELECTDAYTIMECLOCKOUTPUTSRELAYSFIR
ZONESENSE PLUS OPERATION & PROGRAMMING 8 Appendix B: AS4428 ABS Front Panel Configuration Labelling ZONE1CONFIGURATIONNORM / AVF / NON /
Page 26 ZONESENSE PLUS OPERATION & PROGRAMMING 9 Appendix C: Simple Example Wiring Diagram of a Basic FACP + -RS485MONITOREDINPUTSCOM 1
UNCONTROLLED DOCUMENT NOTE: Due to AMPAC’s commitment to continuous imp
Page 1 ZONESENSE PLUS OPERATION & PROGRAMMING AMPACSU 00 : 15STATUSFAULTSTESTISOLATESZONESISOL'DZONE 1ACTIVEZONE 2ACTIVEMENUENTERMENUENTER
Page 2 ZONESENSE PLUS OPERATION & PROGRAMMING 1 Introduction Using 3 levels of access the ZoneSense PLUS Fire Alarm Control Panel ( FACP ) i
Page 3 ZONESENSE PLUS OPERATION & PROGRAMMING Level3: ( Pre-commissioning Password factory set at 3333 ) Level 3 SYSTEM and PROGRAM menus can o
Page 4 ZONESENSE PLUS OPERATION & PROGRAMMING MENUENTERCANCELACFISOLATE 2.4 System Controls For the purposes of this explanation the following
Page 5 ZONESENSE PLUS OPERATION & PROGRAMMING EARTH FAULT Earth Fault – Yellow Is an indication only to warn of a fault to earth that may aff
Page 6 ZONESENSE PLUS OPERATION & PROGRAMMING ZONE 1ZONE 3ZONE 5ZONE 7ZONE 2ZONE 4ZONE 6ZONE 8ALARMFAULT / ISOLATEZONE 1ZONE 3ZONE 2ZONE 4ALARM
Page 7 ZONESENSE PLUS OPERATION & PROGRAMMING 4 Level 1 Access Is a read only menu that allows the operator to reset latched Ancillary Contr
Comments to this Manuals