Ampac FireFinder PLUS Specifications Page 14
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 8
FIREFINDER PLUS
(
AUST
)
INSTALLATION
,
COMMISSIONING OPERATION
4.5 Cabling Recommendations
Conventional Zones
Cabled in red Twin Plastic Sheath (TPS), Fire rated Radox or approved equivalent.
Analogue Loop
Two core cable. The minimum cable size is 0.75mm
2
, the maximum loop resistance is 50 ohms and
the maximum loop distance is 2km.
RS 485 Network
Single twisted pair screened (2 core) cable originating from FACP extending through the protected
areas and returning to the FACP.
Cable Specifications
Capacitance of 100 Pico farads per metre or less
Resistance of 100 milliohms per metre or less
Impedance of loop typical 100 to 120 ohms
Maximum distances between modules 1.2km providing cable meets above specifications.
Recommended cable type
Belden 8132 or 9842 (non fire rated)
Radox FR Communication 0.75mm 1 pair (fire rated) x 2
SmartTerminal
Single twisted pair shielded cable (2 core) plus 2 core power, or local supply. Maximum distance
between from the last SmartTerminal and the FACP is 1.2km.
LED Mimic (RS485)
Single twisted shielded cable (No return loop) plus 2 core power or local supply.
Maximum distance between each LED repeater card and FACP is 1.2km.
Recommended Cable Type
Hartland HC2335
Belden 9841
Radox FR Communication
Fire Alarm Bell Connection
Two core 1.5mm
2
PVC sheathed MIMS (Mineral Insulated Metal Sheathed) to the bell location.
Brigade Connection via Telecom
Two core 1.5mm² PVC sheathed MIMS from the FACP to the Telecom MDF.
RJ45 Multi-drop Serial Port
8 core Flat cable
Power Supplies / AC Mains
The requirement for the mains supply to the FACP is fixed wiring, using three core cable (no less than
0.75mm² and no more than 2.5mm² ) or a suitable three conductor system, fed from an isolating
switch fuse spur, fused at 3A. This should be secured from unauthorised operation and be marked
'FIRE ALARM: DO NOT SWITCH OFF. The Mains supply must be exclusive to the FACP.
- Disabling a Zone / Device 3
- 2 Introduction 8
- 2.3 Compliance 9
- NOTE: WIRING MAY VARY DUE TO 10
- CLIENT PANEL CONFIGURATION 10
- FireFinder PLUS Description 11
- 4.5 Cabling Recommendations 14
- Page 11 17
- 22/09/09 18
- BRD86BPSC4 18
- 4.8.1 Battery Connections 19
- 4.8.3 Monitored Inputs 20
- 4.8.4 Monitored Outputs 21
- Page 16 22
- 4.9 Main Board 23
- KEYSWITCH 24
- BRD86FPB4 24
- 11/08/10 24
- 4.11 Main CPU 25
- 4.12 Slave CPU 26
- Page 21 27
- Page 22 28
- 5.1 System Controls 29
- Page 25 31
- Page 26 32
- 5.2 System Indicators 33
- Page 28 34
- Page 29 35
- 6.4.1 Forgotten Passwords 37
- 7.7 Status 41
- 7.8 Tools 45
- 7.9 Setup 46
- 7.10 About 47
- 8 The Function Menu 48
- to initiate a WALK TEST: 50
- 8.6 I/O 51
- 8.7 Global (Network Panels) 52
- 8.8 Passwords (Level III) 53
- Device 55
- 8.9.9 Mismatch Detected 58
- Page 53 59
- LOOP OR DEVICE 61
- Note: Debug/Noteboo 62
- 12.1 Ancillary Services 63
- 12.3 Expansion Board 64
- Page 59 65
- RS485 Control 66
- Comms Out 66
- 12.7 16 Way Input Board 68
- 12.8 8 Way Relay Board 69
- 12.8.2 Remote Relay Board 70
- - + 71
- 12.10 4 Way Fire Fan Module 72
- 27VDC Out27VDC In 73
- 12.12 Bargraph Display Card 74
- 12.14 SmartTerminal 75
- 12.14.2 Mechanical 76
- Page 71 77
- 12.14.5 Operation 78
- 12.15 Agent Release Control 82
- Page 77 83
- Page 78 84
- 12.15.2 Agent Release Module 85
- Page 80 86
- Page 81 87
- Page 82 88
- Comms In 89
- 12.15.5 Interface Wiring 90
- 12.15.6 Warning Signs 91
- Page 87 93
- Page 88 94
- Polarised 3 Wire Connection 94
- 12.17 Printer 98
- 12.17.2 Maintenance 99
- Page 94 100
- Page 95 101
- IMPORTANT 102
- Page 97 103
- Page 98 104
- Page 99 105
- List of Compatible Devices 106
- AMPAC TECHNOLOGIES PTY LTD 107
- 16.1 Maintenance 108
- Page 103 109
- 17 Compatible Devices 110
- 18 Address Setting 112
- 19 Glossary of Terms 113
- 20 Definitions 114
- 21 Specifications 115
- Page 110 116
- 22 QUICK REFERENCE GUIDE 117
- 23 Statement of Compliance 118
- Page 113 119
- Print Name/s 119
- Please PRINT or Stamp 119
- 23.1 Installation Details 120
- Commissioning Test Report 121
- 24.1 Procedure 122
- 24.2 System Information 122
- Page 117 123
- Page 118 124
Related products and manuals for Fire protection Ampac FireFinder PLUS
Fire protection Ampac ZoneSense User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.349 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals