Ampac FireFinder PLUS Specifications Page 123
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 117
FIREFINDER PLUS
(
AUST
)
INSTALLATION
,
COMMISSIONING OPERATION
including that the receiver responds to signals from an actuating
device for alarm, tamper, low standby power signals and gives a fault
signal when the supervisory signal condition is absent.
(j) Operation of fault and alarm signals: Fault and alarm conditions
correctly detect and indicate as the correct. alarm zone, operating
other required indicators, and operate relevant outputs of the CIE.
(k) Mimic panel:
A
ll mimic panels, annunciators, etc., operate
correctly.
(l) Alarm zone controls: Alarm test, fault test, isolate and rese
t
facility of each alarm zone operates correctly.
(m) Alarm dependency:
A
larm dependency works correctly and
does not apply to devices listed in Clause 3.3 of AS 1670.1.
(n) CIE response to actuating device operation: Each actuating
device has operated when tested with a medium suitable for the
device type and the alarm has indicated on the FIP and at the tested
device.
(o) Fault response time: The response to a fault does not exceed
100 s for each alarm zone circuit.
(p) Alarm response time:
A
t least one detector in each alarm zone
has been tested and the response to the alarm does not exceed 10 s
or the period specified when dependency on more than one alarm
signal is used.
(q) Supervisory signal response time:
A
t least one supervisor
y
device in each alarm zone circuit has been tested and the response
to the supervisory device does not exceed 100 s.
(r) Alarm acknowledgment facility:
A
larm acknowledgemen
t
facilities operate in accordance with the requirements of Clause 3.2
AS 1670.1.
(s) Occupant warning system:
(i) A fault signal is displayed at the CIE when the circuit wiring at the
last speaker or sounder is short or open circuited.
(ii) Each sounder/speaker operates in accordance with the
requirements of Clause 3.22 of AS 1670.1 and a record of the sound
pressure level has been made.
(t) The external alarm indication: is visible from the main approach
to the building.
(u) Manual call points
(i) Each manual call point operates correctly.
(ii) The activation of manual call points do not cause existing detecto
r
alarm indications to be extinguished.
(iii) Manual call points are not subject to alarm dependency.
(v) Smoke and fire door release: Each door-release device
operates correctly.
(w) Flame detectors
(i) The number and type of flame detectors provide adequate
protection for the area.
- Disabling a Zone / Device 3
- 2 Introduction 8
- 2.3 Compliance 9
- NOTE: WIRING MAY VARY DUE TO 10
- CLIENT PANEL CONFIGURATION 10
- FireFinder PLUS Description 11
- 4.5 Cabling Recommendations 14
- Page 11 17
- 22/09/09 18
- BRD86BPSC4 18
- 4.8.1 Battery Connections 19
- 4.8.3 Monitored Inputs 20
- 4.8.4 Monitored Outputs 21
- Page 16 22
- 4.9 Main Board 23
- KEYSWITCH 24
- BRD86FPB4 24
- 11/08/10 24
- 4.11 Main CPU 25
- 4.12 Slave CPU 26
- Page 21 27
- Page 22 28
- 5.1 System Controls 29
- Page 25 31
- Page 26 32
- 5.2 System Indicators 33
- Page 28 34
- Page 29 35
- 6.4.1 Forgotten Passwords 37
- 7.7 Status 41
- 7.8 Tools 45
- 7.9 Setup 46
- 7.10 About 47
- 8 The Function Menu 48
- to initiate a WALK TEST: 50
- 8.6 I/O 51
- 8.7 Global (Network Panels) 52
- 8.8 Passwords (Level III) 53
- Device 55
- 8.9.9 Mismatch Detected 58
- Page 53 59
- LOOP OR DEVICE 61
- Note: Debug/Noteboo 62
- 12.1 Ancillary Services 63
- 12.3 Expansion Board 64
- Page 59 65
- RS485 Control 66
- Comms Out 66
- 12.7 16 Way Input Board 68
- 12.8 8 Way Relay Board 69
- 12.8.2 Remote Relay Board 70
- - + 71
- 12.10 4 Way Fire Fan Module 72
- 27VDC Out27VDC In 73
- 12.12 Bargraph Display Card 74
- 12.14 SmartTerminal 75
- 12.14.2 Mechanical 76
- Page 71 77
- 12.14.5 Operation 78
- 12.15 Agent Release Control 82
- Page 77 83
- Page 78 84
- 12.15.2 Agent Release Module 85
- Page 80 86
- Page 81 87
- Page 82 88
- Comms In 89
- 12.15.5 Interface Wiring 90
- 12.15.6 Warning Signs 91
- Page 87 93
- Page 88 94
- Polarised 3 Wire Connection 94
- 12.17 Printer 98
- 12.17.2 Maintenance 99
- Page 94 100
- Page 95 101
- IMPORTANT 102
- Page 97 103
- Page 98 104
- Page 99 105
- List of Compatible Devices 106
- AMPAC TECHNOLOGIES PTY LTD 107
- 16.1 Maintenance 108
- Page 103 109
- 17 Compatible Devices 110
- 18 Address Setting 112
- 19 Glossary of Terms 113
- 20 Definitions 114
- 21 Specifications 115
- Page 110 116
- 22 QUICK REFERENCE GUIDE 117
- 23 Statement of Compliance 118
- Page 113 119
- Print Name/s 119
- Please PRINT or Stamp 119
- 23.1 Installation Details 120
- Commissioning Test Report 121
- 24.1 Procedure 122
- 24.2 System Information 122
- Page 117 123
- Page 118 124
Related products and manuals for Fire protection Ampac FireFinder PLUS
Fire protection Ampac ZoneSense User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 1.773 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals