Ampac FireFinder PLUS Specifications Page 85
- Page / 96
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 79
EN54 FIREFINDER PLUS INSTALLATION,COMMISSIONING & OPERATION
16 Maintenance and Troubleshooting Chart
16.1 Maintenance
The FireFinder PLUS FACP should be maintained so as to comply with all standards / regulations
applicable to the country and location it has been installed. Failure to do so could put at risk
compliance and the integrity of the system. As a minimum it is recommended the following be used
as a guide to periodic maintenance especially if there is an absence of standards regulations.
General
To implement a site maintenance regime, responsibilities should be established by responsible
persons, training implemented if required, maintenance delegates appointed and all outcomes
clearly communicated to all parties.
Daily Operations (operator level)
The delegated operator checks for normal operation
If any faults are detected, record them in an established “Site Log Book” and report them to
the assigned body.
Ensure all faults are signed off as they are resolved and follow up on those that are still
outstanding.
Monthly Operations (operator level)
In addition to Daily Operational checks
Visually inspect in and around the panel for any signs of pests, moisture or general damage
Ensure any non FACP standby power facilities are in a state of operational readiness
Force a suitable device, such as an MCP or detector, into an alarm state so that it generates
a know alarm outcome. This process should be controlled and established in consultation
with all interested parties (installing engineers include) so that maximum benefit is obtained
from the test.
Ensure the Site Log Book” is up to date, faults have been attended to and the latest test are
recorded
Quarterly Operations (service contractor)
In addition to Monthly Operational checks
Check all internal connections and perform “alarm”, “fault” and site specific tests
Perform a “walk around” of the site to determine if the system integrity is free of possible
faults
Ensure the Site Log Book” is up to date, faults have been attended to and the latest test are
recorded
Annual Operations (service contractor)
In addition to Monthly Operational checks
Initiate both a “lamp” and “walk” test and any other tests as determined necessary for the
site
Inspect and test ( as per the manufacturers specifications ) batteries
Ensure the Site Log Book” is up to date, faults have been attended to and the latest test are
recorded
Replacement Components (service contractor)
Batteries and fuses are seen as the only field replaceable components.
If a board field change is required all necessary anti-static precautions must be taken.
Note: If the Main Board is changed the power supply may require re-calibration.
- FireFinder PLUS 1
- Responding to a Fire 2
- Disabling a Zone / Device 3
- 1 About This Manual 7
- 2 Introduction 8
- SMARTTERMINAL 9
- FIREFINDER FACP 9
- NOTE: WIRING MAY VARY DUE TO 10
- CLIENT PANEL CONFIGURATION 10
- Tap lightly around the 13
- BRD85CLFB 16
- 0V+27V 0V 16
- 22/09/09 19
- BRD86BPSC4 19
- 2 X LIMITED 2A 20
- AUX POWER 20
- AUX OUT1 20
- AUX OUT2 20
- Door Switch 21
- DBA / MCP 21
- 4.8.4 Monitored Outputs 22
- NO C NC 23
- NO C NCNO C NC 23
- 4.9 Main Board 24
- KEYSWITCH 25
- 4.11 Main CPU 26
- 4.12 Slave CPU 27
- LOOP 1 CONTROL 28
- LOOP 2 CONTROL 28
- 5.1 System Controls 30
- 5.2 System Indicators 33
- 6 Functions And Menus 34
- 6.4.1 Forgotten Passwords 35
- 7 The Main Menu 36
- 7.3 Pre-Alarms 37
- 7.4 Faults 37
- 7.5 Disables 38
- 7.6 Walk Tests 38
- 7.7 Status 39
- Network Points: 41
- Remote Slave Modules: 42
- 7.8 Tools 43
- 7.9 Setup 44
- 8 The Function Menu 45
- 8.3 Day/Night 46
- 8.4 Logs 46
- 8.5 TESTS 47
- 8.6 I/O 48
- 8.7 Passwords (Level III) 49
- 8.8 Programming 49
- CONV ZONE: 50
- DEVICE: 51
- To EDIT or to DELETE 51
- 8.8.10 Mismatch Detected 54
- DB9F CONNECTOR 57
- ( Female Rear View ) 57
- 2 CORE SHIELDED CABLE 57
- 12.1 Ancillary Services 58
- 12.3 Expansion Board 59
- + - -+ -+ -+ -+ -+ -+ -+ 60
- RS485 Control 61
- Comms Out 61
- 12.7 16 Way Input Board 63
- 12.8 8 Way Relay Board 64
- 12.8.2 Remote Relay Board 65
- - + 66
- 12.10 4 Way Fire Fan Module 67
- 27VDC Out27VDC In 68
- 12.13 SmartTerminal 69
- 12.13.2 Mechanical 70
- SmartTerminal 1 71
- SmartTerminal 2 71
- (IF FITTED) 71
- Main Panel 71
- 12.13.5 Operation 72
- 12.14 Printer 75
- 12.14.2 Maintenance 76
- Replacement Paper Roll 77
- To Printer (5V) 78
- 27VDC IN 78
- IMPORTANT 79
- Page 74 80
- 12/10/2009 81
- BRD43SPB4 81
- MAIN CONTROL BOARD 82
- 16.1 Maintenance 85
- 17 Compatible Devices 87
- = PUNCH OUT 89
- 19 Glossary of Terms 90
- 20 Definitions 91
- 21 Specifications 92
- Page 87 93
- 22 QUICK REFERENCE GUIDE 94
- Page 89 95
- Assessed to ISO9001 96
- LPCB ref. no 952 96
- (AMPAC Europe) 96
Related products and manuals for Fire protection Ampac FireFinder PLUS
(114 pages)© 2020, manymanuals.com. All rights reserved. | 0.620 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals