Ampac FireFinder Series II AS442 Specifications Page 53
- Page / 114
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Page 48
FIREFINDER SERIES II INSTALLATION, COMMISSIONING &
OPERATION
11.12 Printer
Specifications
Printing method: directed impact dot matrix
Interface: 8 bit parallel interface
Printing mechanism: 4/6 pin shuttle
Interface port: 26 PIN flat plug
11.12.1 Indicators and Buttons
The front panel has an LED indicator and two buttons SEL (SELECT), LF (LINE FEED).
SEL Button
LF Button
TP
INDICATOR
Paper
Paper Cutter
Instructions
Indicator
SEL
LF
Cassette
Ribbon
Press and turn
to tighten ribbon
Press to
Release
Mechanism
PUSH to lock Mechanism
PUSH
Figure 68: Printer Front Panel Layout (Front Cover Closed / Open)
Indicator
When the 3 colour LED indicator is illuminated;
Red indicates the printer is offline with no paper;
Green indicates the printer is On Line;
Yellow indicates the printer is On Line with no paper; or if it is
Off indicates the printer is Off Line or the printer is busy.
SEL Button
a) On Line / Off Line State
The printer enters the On Line state automatically when power is applied or on exiting from the Self-
Test mode. (LED is green).
Press the SEL button, the LED is turned off and the printer goes Off Line.
Press the SEL button again, the LED turns on and the printer is On Line again.
Note: The printer will not receipt data when the printer is off line.
b) Pausing the Printer While It Is Printing.
Press the SEL button while the printer is printing, the printer will pause and enter the Off Line mode
after it finishes printing the row it was currently printing. The printer will continue to print when the
SEL button is pressed again.
c) Enter the HEX-DUMP mode
Remove power from the printer, press the SEL button, then reconnect the printer to the power
supply. The printer will enter the HEX-DUMP mode. In this mode any programs sent from the host
CPU will be printed out in Hexadecimal.
LF Button
While the printer is Off Line press and hold the LF button, paper feed will be initiated. Release the LF
button and the paper feed will be cancelled.
- FireFinder 1
- ACKNOWLEDGE 2
- 1 About This Manual 6
- 2 System Overview 7
- NOTE: WIRING MAY VARY DUE TO 8
- CLIENT PANEL CONFIGURATION 8
- 3 FireFinder Description 9
- OPERATION 10
- Tap lightly around the 11
- 4.7 Cabling Recommendations 12
- 4.6 Operational Parameters 12
- - + -- + -- + 18
- Door Switch 20
- DBA / MCP 20
- 4.11 Main Board (BRD85MBA) 21
- 4.13 Main CPU (BRD85CPU) 23
- 4.14 Slave CPU (302-669) 24
- 5 FireFinder Control Panel 28
- FUNCTION 30
- 6 Functions And Menus 31
- 7 The Main Menu 32
- Apollo Loop No: 1 33
- REMOTE MODULE STATUS 33
- 7.2 Testing Menu 34
- 8 Main Functions 35
- PASSWORD MENU 37
- SELECT NO 37
- 8.7.1 Forgotten Passwords 38
- Zone: 39
- DEVICE: 40
- to EDIT or to DELETE 40
- IN A PANEL 40
- ON A LOOP 40
- OUTPUT: 40
- PROGRAMMING MENU 41
- 1: ON SITE PROGRAMMING 41
- SELECT NO: 41
- L1 S1 Z17 ALARM 43
- 5/7/2005 15:12:10 43
- SENSOR ALARMS 1 OF 5 43
- 11.1 Ancillary Services 45
- CN3 I/P 1-16 47
- CN4 O/P 9-16 47
- CN5 O/P 1-8 47
- 302-6770 48
- Clear Plastic Clip In Label 49
- Top OverLay 50
- All Fuses are 1A M205 Style 52
- 11.12 Printer 53
- Paper Cutter 54
- Replacement Paper Roll 55
- To Printer (5V) 56
- 27VDC IN 56
- 11.13 Agent Release Control 57
- SERVICE INHIBIT 60
- COMMON FAULT 62
- LIFT COVER AND PRESS BUTTON 63
- TB5TB4TB3 64
- Solenoid 65
- 11.14 Warning Signs 66
- BRD 42WTB2-A 67
- LINE FAULT 69
- Page 65 70
- 11.16 EV60 / 120 72
- 11.17 EV3000 72
- 12 Brigade Devices 73
- IMPORTANT 74
- 14 SmartTerminal 80
- 14.2 LCD Screen Format 84
- System Status 85
- A - A + C - C+ 85
- 14.3 Operation 86
- 14.4 Setting the Address 87
- 14.5 Mechanical 88
- 14.7 Specifications 90
- ConfigManager 91
- HEAD OFFICE 95
- 18 Troubleshooting Chart 96
- 19 Address Setting 97
- 20 Glossary of Terms 98
- 21 Definitions 99
- 22 Quick Reference Guides 100
- Quick Reference 101
- No 102
- 24.1 Procedure 106
- 24.2 System Information 106
Related products and manuals for Fire protection Ampac FireFinder Series II AS442
Fire protection Ampac ZoneSense User Manual
(28 pages)
(28 pages)
© 2020, manymanuals.com. All rights reserved. | 0.730 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals